Wood & steel frame
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Kirby, TX
Gate problems in Kirby usually come down to two things: the clay soil shifting under your posts, and the sun and humidity eating at the metal. Most Kirby homes were built between the 1950s and 1980s, and many of those original gates – lightweight tubular steel or chain-link – were never reinforced for this soil. When the ground swells after a storm, posts lean. When the latch won’t line up, you can’t close the gate. Calder Gate Repair handles that all day. Call (361) 314-4803 and we’ll give you a written price before we touch a bolt.
Why Kirby Homes Are Different
Kirby sits on expansive clay soil, which is a polite way of saying the ground moves. After a heavy rain, the soil swells. During a dry stretch, it shrinks and cracks. Gates bolted to posts set in that soil don’t stay square for long. We see sagging gates, hinges pulling loose from brick veneer, and latches that drift out of alignment year after year.
The east side of Kirby has its own wrinkle. A lot of properties near Ackerman Road are flanked by mature live oaks, and those roots push up concrete walkways. When the concrete lifts, gate posts tilt with it. That’s a post reset plus a hinge realignment before the gate ever moves smoothly again. Newer subdivisions don’t have this problem because the trees haven’t had forty years to spread.
And then there’s the humidity. Kirby summers are hot and wet, and metal gates corrode faster than most homeowners expect. Wrought-iron looks sturdy until you check the bottom rail and find it’s rusted from the inside. We account for that when we quote, because a repair on a rust-weakened frame won’t hold the way it would on a newer gate.
Many Kirby properties are also corner lots near Randolph AFB. Military families move in and out regularly, and gates get neglected during transitions. A gate that hasn’t been adjusted in a few years is usually out of square, rusted at the hinges, or dragging on the ground. The good news: none of that requires a full replacement if it’s caught early.
Styles & brands we work with
Our Main Kirby Services
Most Kirby calls fall into three buckets: the gate itself is sagging or stuck, the electric motor isn’t responding, or the opener has died entirely. Each one has its own page with full pricing.
Gate Repair in Kirby
A Kirby gate repair usually starts with the posts. Clay soil moves them, and once a post leans even half an inch, the gate catches on the concrete or the latch stops lining up. We reset posts, replace rusted hinges, repair sagging frames, and re-align latches on chain-link, tubular steel, and wrought-iron gates. Older Kirby gates often use lightweight steel that rusts at the weld points first, so we inspect the frame before recommending any repair over replacement. If the frame is sound, we fix it. If it’s not, we tell you before we quote a single part. Full details and pricing are on the Gate Repair in Kirby page.
Electric Gate Repair in Kirby
Electric gates in Kirby fail differently than manual gates because the motor keeps working while the ground moves. The gate might cycle fine for a year, then one storm swells the clay and the gate binds against the post. The opener doesn’t know the gate is jammed – it just trips the safety sensor or burns out the capacitor trying. We see this on Linear and Viking openers regularly around Kirby. We check the gate travel first, then the motor, then the control board. It’s usually one of those three, and the repair is often finishable same day. Read the full breakdown on the Electric Gate Repair in Kirby page.
Gate Opener Repair in Kirby
Opener problems in Kirby split between two causes: electrical failures inside the unit and physical binding from the gate itself. If the opener hums but nothing moves, it’s often a capacitor or a stripped gear. If it clicks and does nothing, it’s usually the board. Ghost Controls and DoorKing openers are common in Kirby, and both have known failure points we can diagnose over the phone before we dispatch. We keep parts for those brands stocked locally, which shortens turnaround. The Gate Opener Repair in Kirby page has the full price list and details on what gets replaced versus repaired.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Kirby
We work on Linear, Viking, Ghost Controls, and DoorKing openers every week across Kirby. We stock the common boards, capacitors, and limit switches for those brands, which means many opener repairs happen in a single visit. You can see the full list on our brands page.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Kirby, TX
| Service | Typical range in Kirby |
|---|---|
| Gate realignment (hinges, latch, no parts) | $90 – $180 |
| Post reset (single post, concrete included) | $150 – $300 |
| Hinge replacement (pair) | $60 – $140 |
| Latch or lock replacement | $45 – $110 |
| Chain-link gate frame repair | $120 – $260 |
| Wrought-iron rust repair and repaint (per section) | $180 – $350 |
| Opener diagnostic | $49 – $89 |
| Opener board replacement | $180 – $400 |
| Capacitor or gear replacement | $90 – $220 |
| Limit switch adjustment or replacement | $70 – $150 |
What drives a Kirby quote higher than the base range is usually what we find underneath: posts that need to be reset before the gate can be aligned, or rust damage that means a weld won’t hold. We tell you the full price before work starts, and that’s the number on the invoice. Always.
Neighborhoods We Serve in Kirby
We cover all of Kirby, and our crews are usually out there every weekday. Same-day response is common for repair calls placed before noon, especially east of Binz-Engleman where the older subdivisions are concentrated.
- Ackerman Road area
- Kirby Heights
- Springfield subdivision
- Old Kirby (west of Binz-Engleman)
- Corner lots near Randolph AFB
Service Area – Cities Near Kirby
Kirby sits on the northeast edge of San Antonio, and we handle gate work throughout the surrounding area. If you’re in San Antonio, TX, we cover most of the east and northeast sides. We also serve Cibolo, TX, Helotes, TX, and Selma, TX – each with the same upfront pricing and written guarantee.
Serving Kirby, TX - Our Local Coverage Area
We’re based in the Kirby area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kirby
Most Kirby repair calls are answered same day if you call before noon. Opener diagnostics and simple realignments often finish in a single visit. We don’t give you a four-hour window – we give you a live arrival time you can track, and a text when the tech is on the way.
For repair work – realignment, hinge replacement, opener swaps – no permit is typically required. New gate installations or major driveway changes may need city approval depending on the scope. We’ll tell you during the quote if anything on your job looks like it needs a permit.
Always. Every Kirby job starts with a written price that covers labor and parts. If we find something unexpected underneath, we stop and re-quote before touching anything further. The invoice you get at the end matches the number you agreed to at the door.
If your gate won’t close or your opener quit, call Calder Gate Repair at (361) 314-4803. We’ll give you a real price, a real arrival time, and a repair that’s covered by our 365-Day Done Right Promise in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kirby Customers Say
"Booking was easy and the job was done quickly."
- Seth R."Swing gate arm replaced and aligned. Got photos of the old part by text."
- Nadia F."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.