Wood & steel frame
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in San Antonio?
Gate repair in San Antonio typically costs $185 to $460 for most common fixes, with gate opener repairs landing between $225 and $550 before parts. Full gate replacement runs $1,400 to $5,200 depending on material, length, and automation. These are 2026 San Antonio market prices: higher than Dallas, lower than Austin, and shaped by our soil, heat, and the sheer number of wrought iron and steel gates across neighborhoods like Alamo Heights, Stone Oak, and Helotes.
Most repairs we complete in one visit. Written estimates are always free from Calder Gate Repair San Antonio, and you’ll get a firm price before any work starts. Call (361) 314-4803 anytime, day or night.
Gate Repair Cost Breakdown (2026)
Here is what San Antonio homeowners actually pay for gate repairs in 2026. These ranges reflect labor plus standard parts, drawn from service calls across the city from downtown to Far West Side.
| Repair Type | Typical Cost Range | Notes |
|---|---|---|
| Gate opener repair (control board) | $225 – $450 | Includes diagnostics, board replacement, reprogramming |
| Gate opener replacement (motor only) | $450 – $900 | Labor plus mid-range motor; price varies by brand |
| Hinge replacement (steel, pair) | $160 – $340 | Includes grinding off old hinges, welding or bolting new ones |
| Sagging gate realignment | $120 – $280 | Adjusting hinges, frame, or post alignment |
| Welding repair (cracked frame) | $140 – $320 | Per crack or joint; most gates need one to three welds |
| Keypad or intercom replacement | $165 – $385 | Labor plus hardware; wireless keypads run lower |
| Sensor or limit switch replacement | $130 – $260 | Limited switch issues are the most common opener fault |
| Full gate replacement (steel, single swing) | $1,400 – $3,800 | Includes labor, gate, hardware, and haul-away |
| Full gate replacement (ornamental, double swing) | $2,800 – $5,200 | Heavier fabrication, dual openers, longer install |
What drives a quote up or down: the brand of opener you own (a LiftMaster is easier to source than an older FAAC board), whether the gate is welded steel or bolt-together aluminum, how far the gate sits from your house, and whether the post itself has shifted in San Antonio’s clay soil. Clay is the quiet culprit behind a lot of gate issues here. In wet years the soil swells, in droughts it shrinks, and a gate that cleared perfectly in May drags by August. We account for that when we diagnose, because a repair that ignores soil movement will fail within a season.
What Affects Gate Repair Pricing in San Antonio
- Opener brand and age. We work on nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Older FAAC and Viking boards cost more to source than current LiftMaster or Ghost Controls parts, and that shows up in the quote.
- Gate material and weight. A solid steel ornamental gate in Terrell Hills weighs more than an aluminum tube gate in Cibolo. Weight affects motor load, hinge stress, and the time it takes to remove and rehang the gate.
- Soil movement and post condition. San Antonio sits on expansive clay. Posts shift. If the post has moved, the repair isn’t just “tighten the hinge.” It means digging, resetting, and sometimes re-pouring a footer, which adds $200 to $600.
- Access and clearance. Gates built close to walls or fences, or gates on slopes like those common in the Hill Country north of 1604, take longer to work on. Steep driveways mean we set up differently and often need an extra set of hands, especially on double swing gates.
- Electrical runs and existing wiring. If the wire from your house to the gate is buried and failing, a new run can add $150 to $400 depending on distance and whether we’re going under concrete or landscaped beds.
- Time of year. Summer heat pushes gates to fail at higher rates. June through September is our busiest stretch, and while our rates stay flat year round, some parts suppliers run short on popular boards in peak season, which can add a day or two for sourcing.
How to Save on Gate Repair
You don’t have to overspend to get a gate fixed properly. Here’s what actually saves money in San Antonio.
- Catch hinge wear early. A gate that squeaks or sags by half an inch is maybe a $120 adjustment. Wait until the hinge tears out of the post and you’re looking at $300 or more plus welding.
- Don’t keep forcing an opener that groans. When an opener motor strains against a heavy gate, it burns out faster. A sticking gate plus a dying motor means two repairs. Fix the gate movement first, then the opener.
- Buy the right opener once. If your old opener is a brand we can’t source parts for quickly, replacing it with a current LiftMaster or BFT model often saves money over chasing obsolete boards every two years.
- Ask for the written estimate. Every Calder Gate Repair job gets a written price before work starts. No bidding wars, no surprises on the invoice.
- Take advantage of the free estimate. Call (361) 314-4803 and we’ll come out, diagnose, and put a number in writing. You’re not obligated to anything.
What Does Gate Opener Repair Cost in San Antonio?
Gate opener repair in San Antonio runs $225 to $550 for most jobs, with some board-only repairs on premium brands going slightly higher. A full motor replacement lands between $450 and $900 including labor. If you’re nursing an opener older than 12 years with a failing control board, we’ll often tell you honestly: replacement beats repair on cost per year.
The most common opener failure we see is the control board. In San Antonio’s heat, boards bake inside their metal housings, especially on west-facing gates that catch full afternoon sun in neighborhoods without shade. Symptoms: the gate opens but won’t close, the remote stops responding, or the gate reverses for no reason. We replace boards same-day when the part is in stock, and we carry boards for the most common LiftMaster, Linear, and BFT models on our trucks.
Brand-Specific Repair Notes
- LiftMaster is the easiest brand to repair here. Parts are affordable and widely available in San Antonio. Most LA400 and LA500 series issues we fix in one visit.
- FAAC openers are common on older estate gates in Alamo Heights and Olmos Park. Boards can be expensive and sometimes take two to three days to source.
- BFT units are rugged but parts circulate through fewer suppliers. Diagnostic work matters more with these because a misdiagnosed sensor issue sends you down a costly path.
- Mighty Mule and Ghost Controls are the DIY-friendly openers. When they fail, it’s often the control board or a burned transformer, and repair cost is on the lower end, usually under $400.
- Viking and DoorKing show up at commercial properties and larger residential estates. These are workhorse units, but component costs run higher, and solar-charged battery systems in Viking gates need more routine care in our climate.
How to Tell If You Need Gate Repair or Replacement
The short answer: if the frame is structurally sound, repair almost always wins. If the steel is rusted through, the post is split, or the opener is beyond parts availability, replacement is cheaper over three years.
Repair vs. replacement thresholds break down like this:
- Rust through the bottom rail or hinge mounts: replacement. Patching rusted steel is a temporary fix that fails again within a year or two.
- Single cracked weld: repair. A $180 weld buys years of life on an otherwise solid gate.
- Post leaning more than an inch: depends. If the post is steel and set in concrete, we can often straighten and re-anchor it. If the post is a rusted-out box with crumbling concrete, replacement is the honest call.
- Opener over 15 years old with a dead board: replacement. An obsolete board that costs $500 today is a bad bet when a new opener with a warranty costs $600 to $800 installed.
When we replace a gate, we quote the full number up front: fabrication or sourcing, installation, hardware, opener integration, and haul-away. That written price is what you pay. No line-item drift.
Common Gate Problems We Fix in San Antonio
- Sagging gate. After years of heat and soil movement, hinge bolts stretch and gates drop. We realign, replace hinges, and sometimes add an anti-sag kit, typically $120 to $340.
- Gate opener hums but won’t move. Almost always the capacitor or the gear assembly. Capacitor jobs are often under $200. Worn gears run higher, around $250 to $400.
- Remote range dropped to nothing. Could be the receiver board, antenna, or interference. Sometimes freshening the antenna position fixes it for under $100. Board replacement runs $225 to $450.
- Gate reverses or stops halfway. This is a limit switch problem, the small sensor that tells the gate when to stop. Limit switch replacement runs $130 to $260 on most brands.
- Keypad dead. Replace the keypad, not the whole system. Wireless keypads for LiftMaster and Linear units run $165 to $385 installed.
- Gate won’t latch. On swing gates this is either the latch catch or alignment. On slide gates it’s usually the end stop. Simple fixes, typically under $200.
The Calder Gate Repair Process: What to Expect
- Call us at (361) 314-4803. A live person answers, 24/7. No phone tree, no voicemail. We’ll book a time and send a trackable arrival window.
- A uniformed, background-checked technician arrives. They diagnose the gate, explain what they found in plain language, and give you a written quote before any work starts.
- You approve the price. If you want to sleep on it, that’s fine. The written quote is valid and there’s no pressure.
- We complete the repair. Most jobs finish in one visit, same day. You get before and after photos and a digital invoice you can pay from a link.
- You get the 365-Day Done Right Promise in writing. If the repair fails within 365 days, we return at no charge. Not a pro-rated promise, not a warranty buried in fine print. A free second visit.
This is the Relay Standard, named and defined: a live arrival time you can track, before-and-after photos, and a digital invoice you settle from your phone. That’s the booking to invoice experience, and it’s what makes hiring Calder Gate Repair different from calling a random handyman from a search ad.
Gate Repair Costs by San Antonio Neighborhood
Our pricing is consistent across the city, but the type of gate you own varies by area, and that affects what you’ll likely pay.
- Alamo Heights and Olmos Park: Older estate properties with heavy ornamental steel and FAAC or Viking openers. Repairs here trend toward the higher end of our ranges because of gate weight and brand-specific parts.
- Stone Oak and Sonterra: Large subdivision gates, mostly LiftMaster and BFT openers. Mid-range repair costs, and we stock common parts for these brands on the truck.
- Helotes and Grey Forest: Hill Country terrain with sloped driveways and long electrical runs. Expect a bit more labor time, and occasional wire replacement if the original run is failing.
- Far West Side and Alamo Ranch: Newer construction, mostly aluminum tube gates and Mighty Mule or Ghost Controls openers. Repairs trend lower, and opener replacement is straightforward.
- Southtown and King William: Historic properties with tight clearances and older steel gates. Access time adds a bit, and we’re careful with period-appropriate hardware where the owner wants to preserve it.
Why Gate Repair Costs What It Costs
Gate repair is a skilled trade that spans three disciplines: mechanical work, low-voltage electrical, and often welding. The technician who shows up at your gate needs to know how a FAAC board communicates with a set of photo eyes, how to perform hinge & post repair without warping the frame, and how to recalibrate a limit switch so the gate stops precisely without slamming. That’s not a handyman skill set, and the pricing reflects it.
We send background-checked, uniformed technicians who are factory-familiar with nine major brands. That training time costs money, and it’s why we can diagnose a Linear opener issue in 20 minutes that someone else chases for two hours. You pay for the fix, not the learning curve.
Our pricing also includes guarantees that aren’t optional add-ons. Every job gets a written price before work starts and a written guarantee. Every repair carries the 365-Day Done Right Promise, which means if the fix fails within a year, we come back free. That promise is part of the price you pay, and it costs us money to honor it. We’re fine with that because repairs that hold cost less over time for everyone.
FAQs – Gate Repair Cost in San Antonio
How much does gate repair cost in San Antonio?
Most gate repairs in San Antonio run $185 to $460, with gate opener repairs between $225 and $550. Call (361) 314-4803 for a free written estimate on your specific gate.
How much does it cost to fix a gate opener?
Gate opener repair typically costs $225 to $550, depending on the brand and whether the control board, gears, or motor is the culprit. Full opener replacement runs $450 to $900 installed. Call (361) 314-4803 for an exact quote; we diagnose in one visit.
Is it cheaper to repair or replace a gate?
If the gate frame is structurally sound, repair is almost always cheaper, usually $185 to $460. If the frame is rusted through or the post is split, replacement at $1,400 to $5,200 saves money over repeated repairs. We’ll give you an honest recommendation and a written quote either way.
How much does a new gate opener cost in San Antonio?
A new gate opener installed in San Antonio runs $450 to $900 for most residential units from LiftMaster, BFT, or Ghost Controls. Heavy-duty openers for large ornamental gates run higher. Call (361) 314-4803 for a free estimate.
Can you fix my gate the same day?
In most cases, yes. We stock common LiftMaster, Linear, and BFT parts on our trucks, and many repairs are completed in one same-day visit. Call (361) 314-4803 as early as possible and we’ll give you a straight answer on timing.
Do you charge for estimates?
No. Estimates are free. You get a written quote before any work starts, and that quoted number is the number you pay. Call (361) 314-4803 to book.
Get a Free Estimate for Gate Repair in San Antonio
If your gate is sagging, sticking, or your opener has stopped responding, search gate repair near me in San Antonio, TX or call Calder Gate Repair San Antonio at (361) 314-4803. A live person answers 24/7. We’ll schedule a visit, send a trackable arrival time, and put a written price in your hands before a single bolt is turned. Free estimates, no pressure, and a 365-Day Done Right Promise on every repair.
Calder Gate Repair is the dedicated gate repair specialist inside the Relay Home Co. family, founded in 2009. Each location is independently owned and operated under The Relay Visibility Guarantee. We serve San Antonio and surrounding areas from Stone Oak to Southtown to Helotes. Whether you have a LiftMaster that’s gone silent or a FAAC that’s been acting up since the last big storm, we know the system and we’ll fix it right the first time.
Pricing reflects the San Antonio market as of 2026. Calder Gate Repair San Antonio offers free estimates – call (361) 314-4803.
Written by Nico Alvarez, Owner at Calder Gate Repair San Antonio, serving San Antonio since 2009.
What Our Customers Say
"Booking was easy and the job was done quickly."
- Seth R."Swing gate arm replaced and aligned. Got photos of the old part by text."
- Nadia F."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.