Wood & steel frame
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Opener Repair in San Antonio: What to Know First
FAAC gate opener repair in San Antonio typically runs $190 – $460 for most common failures, and we can usually get your gate moving again within one to two business days depending on the part. Calder Gate Repair San Antonio is an independent FAAC service provider, not a factory-authorized shop, which means we fix what’s actually broken without pushing unnecessary replacement hardware. If your FAAC opener is dead, grinding, or refusing to close, call (361) 314-4803 and we’ll give you a straight answer and a written price before anything comes apart.
This page is for San Antonio homeowners with an FAAC swing-arm or slide gate opener who want to understand what went wrong, what it should cost, and whether it’s worth repairing. Nico Alvarez and our team have worked on FAAC 400, 412, 750, 760, and C720 series operators across San Antonio neighborhoods like Alamo Heights, Stone Oak, the Pearl District, and Terrell Hills. If you own an FAAC gate, this is the repair resource we wish every homeowner had before picking up the phone.
How FAAC Products Fail – and How We Fix Them
- FAAC 400 and 412 swing operators: capacitor failure after heat cycles. These compact operators pack a starting capacitor that lives under the cover and gets cooked by Texas sun absorbed through dark metal housing. The symptom is a gate that hums but won’t start, or starts only after you nudge it. We keep OEM-spec capacitors on the truck and replace them in about 40 minutes. If the capacitor tests fine, we move to the limit switch assembly before touching anything else.
- FAAC 750 and 760 slide operators: limit switch drift on long runs. On longer driveway slide gates, the magnetic limit switches slowly shift out of position, especially after heavy rain softens the ground and the gate track settles. You’ll see the gate stop short of fully open, or slam hard into the end stop. We realign and torque the limit assembly, then run the gate through a full cycle test while watching the force settings so it doesn’t come back in six months.
- C720 series control boards: blown motor relays after power surges. San Antonio gets real lightning storms, and FAAC boards are sensitive to surge damage even when the breaker doesn’t trip. If your keypad lights up but the gate doesn’t move, and you’ve already checked the capacitor, it’s usually a relay on the board. We can often repair the board at the component level instead of selling you a new one, which saves $200-$400 on C720 systems.
- FAAC hydraulic 770 and 790 operators: slow oil leaks that get ignored too long. These are the E01 and 400-operator siblings that show up on heavier ornamental iron gates around the Pearl District and Monte Vista. A small fluid leak at the top of the pump body causes sluggish movement and eventually burns out the motor windings as it runs dry. We’ll catch the leak, replace the seal, refill with the correct hydraulic fluid, and check shaft play before it eats the whole operator.
- Aftermarket photobeam and safety edge mismatches. FAAC safety input wiring is picky about resistance values on aftermarket photocells and edges. A lot of FAAC gates in San Antonio stop closing because a previous repair used a generic photocell that the board now reads as a permanently blocked beam. We stock FAAC-compatible safety devices and know which aftermarket units actually work, so you’re not locked out for a week waiting on a mystery part.
Styles & brands we work with
Our FAAC Gate Opener Repair Process
- 1
You call, a person answers. There’s no phone tree. We ask what the gate is doing (or not doing), get your cross streets, and book a window with a live, trackable arrival time.
- 2
Nico or a trained tech arrives and listens first. We run the gate through its cycle, check error codes if the board has them, and test the basics before opening a single cover. You’ll get a text when we’re 20 minutes out.
- 3
You get a written diagnosis and price. We identify the failed component, explain it in plain words, and quote the part and labor separately. OEM and quality aftermarket options are laid out with plain-English trade-offs. If the price isn’t in writing, it isn’t real, so nothing starts until you’ve seen the number.
- 4
We do the repair. We replace the failed part, torque connections to spec, re-lubricate pivot points, and reset open and close limits. We never use used parts unless you specifically ask, and we don’t install parts we wouldn’t put on our own gate.
- 5
We test it properly. Full cycle test, force check, safety device verification, and a final listen for anything that sounds like it won’t last. We film the before-and-after on our phone and you get the clips in your invoice link.
- 6
You get the guarantee in writing. Every FAAC repair carries the 365-Day Done Right Promise. If the same failure comes back within a year, we return at no charge. And if the repair isn’t right, Calder makes it right with a free second visit.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Opener Repair Costs in San Antonio
Most FAAC gate opener repairs in San Antonio fall between $190 and $460 before any optional parts, with the majority of jobs landing around $280. Here’s what we typically see:
- Capacitor replacement on FAAC 400/412: $190 – $260 total
- Limit switch realignment or replacement: $210 – $320 total
- Control board relay repair (component level): $250 – $380 total
- Photobeam or safety edge replacement (compatible): $180 – $300 total
- Full hydraulic seal and fluid service on FAAC 770/790: $340 – $520 total
- Complete operator replacement if yours is beyond repair: $800 – $1,600 installed, depending on model and gate weight
What moves the price: part availability (some FAAC boards have a 3-5 day lead time if we have to order OEM), how long the gate has been running wounded, and whether previous repairs used mismatched parts. You’ll know the exact number before we start. Call (361) 314-4803 for a free estimate on your specific FAAC model.
Why San Antonio Homeowners Call Calder Gate Repair San Antonio for FAAC Work
We’re the gate repair specialist inside the Relay Home Co. family, which means we pair deep FAAC experience with the Relay Standard: a live arrival time you can track, before-and-after photos, and a digital invoice you pay from a link. No vague four-hour windows. No surprise charges at the door. Every job gets a written price before work begins, a written guarantee on the repair, and a free second visit if the repair fails within 365 days. That’s not marketing language. It’s three non-negotiable conditions we put on every single FAAC job.
We also know the rest of the gate opener world. If you have a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing opener on another gate at your property, our techs can diagnose that too. Calder Gate Repair San Antonio has been part of the Relay Home Co. family since 2009, and each location is independently owned and operated under the Relay Visibility Guarantee.
FAQs
We can diagnose it, but we won’t perform warranty work. If your FAAC opener is under the manufacturer’s warranty period, we’ll tell you how to file a claim and can recommend a factory-authorized service provider if one is available in San Antonio. If you’d rather not wait or the warranty was voided by previous work, we’ll repair it as an independent FAAC service provider and stand behind our own 365-Day Done Right Promise.
We stock the most common FAAC wear items on the truck: capacitors, limit switches, photobeam kits, safety edges, and hydraulic fluid. Control boards for the C720 and some older FAAC 750/760 models may need to be ordered, which typically takes 3-5 business days. We’ll tell you upfront if your part isn’t on the truck so you can plan around the gate being down. Call (361) 314-4803 and we’ll check availability for your specific model before you book.
If the repair cost is under 50% of an equivalent new operator, repair makes sense. FAAC operators are built well and most failures are wear items like capacitors, limit switches, and relays, not the motor or gearbox itself. When we do recommend replacement, it’s because the motor windings are cooked or the housing is so corroded that more failures are coming. We’ll give you both options in writing and let you decide.
Most FAAC repairs are scheduled within 24-48 hours in San Antonio. If your gate is stuck open and your security depends on it closing tonight, call (361) 314-4803 and a live person will work with you on emergency availability. We answer calls 24/7, not a voicemail, not a chatbot. You’ll speak with someone who knows the difference between a swing arm and a slide operator.
Yes. We service the FAAC 770 and 790 hydraulic operator series regularly on the ornamental iron gates around the Pearl District, Monte Vista, and Alamo Heights. The most common issue on these in San Antonio is slow fluid loss at the pump seal, which owners often miss until the gate starts moving noticeably slower in winter when the fluid thickens. We replace the seal, refill with the correct fluid, and adjust the bypass valves to factory spec.
Written by Nico Alvarez, Owner & Lead Gate Technician, Calder Gate Repair San Antonio at Calder Gate Repair San Antonio, serving San Antonio and nearby areas.