Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The San Antonio Owner’s Guide

Ghost Controls keypad and intercom repair in San Antonio typically runs $145 – $320 installed, depending on whether we’re replacing the wireless keypad, the intercom module, or the control board connection. Most jobs we handle same-day because we keep Ghost Controls-compatible keypads and intercom parts on the truck. The usual call starts the same way: the keypad stopped responding, or the intercom buzzes but won’t release the gate. Sometimes it’s a dead battery. More often in San Antonio, it’s heat damage, a corroded terminal, or a receiver that’s simply worn out after years of exposure to our summers.

Call (361) 314-4803

Here’s the short version: if your Ghost Controls keypad is dead, intermittent, or your intercom won’t open the gate, we diagnose it on site, show you the failed part, quote a written price, and usually have it working again before you finish your next cup of coffee. Nico Alvarez has run these calls all over San Antonio, from Stone Oak to Alamo Ranch to Terrell Hills, and the fix is almost always faster and cheaper than owners expect once the right part is in hand.

Key Takeaways

• Ghost Controls keypad and intercom repair in San Antonio averages $145 – $320 installed for most single-part replacements.
• We stock Ghost Controls-compatible keypads, intercom modules, and receiver boards on our trucks for same-day repair.
• Heat and humidity are the leading killers of Ghost Controls exterior keypads and intercoms in South Texas.
• You get a written price before work starts, a 365-Day Done Right Promise, and a free second visit if the repair fails.
• Call (361) 314-4803 and a live person answers, 24/7.

Which Ghost Controls Models This Applies To

Ghost Controls makes a few keypad and intercom variants, and matching the right replacement is where we see most DIY attempts go sideways. The most common units in San Antonio are the AXP1 wireless keypad, the AXI intercom module, and the older DTP1 keypad that shipped with many single and dual gate kits. The AXP1 communicates directly with the Ghost Controls receiver on the control board via a paired wireless signal. The AXI intercom wires into the opener’s accessory terminal and lets a visitor call the house; the owner then presses a button on the indoor unit to release the gate.

The compatibility gotcha: Ghost Controls changed receiver protocols between early production runs and current models. A keypad from a 2018 kit will often not pair with a 2023 control board, and vice versa. We check the model sticker on your keypad or intercom module, confirm the board revision, and match the replacement before we quote anything. For most San Antonio installations, we use OEM Ghost Controls parts when they’re available locally or shippable quickly, and we’ll recommend a quality aftermarket equivalent when the OEM part is backordered and the aftermarket unit has a reliable track record. We’ll always tell you which one we’re quoting and why.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Keypad is dead, no beep, no backlight: This is usually a dead battery or a failed keypad board. If fresh batteries don’t revive it, the keypad’s internal seal has likely failed and moisture got to the circuit board. We see this most often after heavy San Antonio rain seasons.
• Keypad beeps but gate won’t move: The keypad is transmitting, but the receiver isn’t accepting the code. This points to a pairing loss or a failing receiver on the control board. Sometimes it’s a blown fuse on the board itself, which is a cheap fix we can do in minutes.
• Intercom buzzes but won’t release the gate: The intercom wiring is intact, but the relay on the indoor unit or the accessory terminal on the opener board has failed. We test the relay first; if it’s dead, a new intercom module solves it.
• Gate opens randomly on its own: A failing keypad can send phantom signals, but in San Antonio, this is more often a receiver picking up interference from a neighbor’s opener or a nearby radio tower. We check for stray signals before condemning the part.
• Works fine in cool weather, dies in the afternoon: Classic symptom of heat-stressed electronics. Ghost Controls units are built for outdoor use, but Texas summers push them hard. An intercom or keypad that fails only when the sun is high is telling you the internal components are degrading.

Replacement Cost & What’s Included

Ghost Controls keypad replacement in San Antonio typically runs $145 – $220 installed for a wireless keypad. Intercom module replacement lands between $180 – $320 installed depending on whether we’re replacing just the outdoor call station or the indoor receiver as well. If the problem is a failed receiver on the opener board itself, the repair is usually $95 – $180 for board-level work. These prices include the part, labor, programming, testing, and our written warranty.

Here’s what drives the range:

• Part type: OEM Ghost Controls parts cost more than quality aftermarket equivalents. We quote both when both are viable.
• Access: Keypads mounted on stone pillars or behind landscaping take longer to access and replace.
• Wiring condition: Older San Antonio homes with existing intercom wiring sometimes need a new wire run if the original has corroded or been cut during landscaping work.

Every quote is written before we start. The number on the invoice is the number we agreed to. No surprises. And if the repair fails within 365 days, we come back free under the 365-Day Done Right Promise. That’s the Calder Gate Repair standard, and we don’t make exceptions to it.

DIY or Call Us?

Ghost Controls keypads and intercoms are low-voltage accessories, so the work isn’t dangerous in the way a high-tension spring or a gate motor capacitor is. That said, the practical failure point for DIY repairs is almost always pairing and programming. Ghost Controls uses a specific pairing sequence, and if you miss a step, the keypad will look dead when it actually isn’t. We’ve showed up to more than a few San Antonio homes where a homeowner replaced a keypad themselves, got stuck on the pairing, and had to call us anyway.

What can you safely check? Fresh batteries, a clean keypad face, and making sure the wiring at the intercom terminal block isn’t loose or corroded. That’s the limit. If the keypad is physically cracked, the intercom relay clicks but won’t release, or the opener board shows no response to any accessory, stop and call us. We’ll diagnose it on site, show you the failed part, and give you a written price before we touch a screwdriver. Call (361) 314-4803 and we’ll get you sorted.

FAQs