Wood & steel frame
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in San Antonio?
Gate Repair services in San Antonio typically cost $185 to $650 for most common fixes, with gate opener replacement running $350 to $1,400 depending on the brand and horsepower. Small adjustments like limit switch recalibration or sensor realignment sit at the lower end, while full hinge rebuilds, circuit board swaps, or welded frame repairs land higher. Most San Antonio homeowners pay $275 to $450 for a typical service call that includes parts and labor.
What you pay depends on three things: the type of gate (swing or slide), what failed (mechanical hardware versus opener electronics), and which opener brand you own. Calder Gate Repair Near Me in San Antonio, TX gives every homeowner a written price before any work starts, so the number you agree to at the door is the number on the invoice. No surprise line items.
Gate Repair Cost Breakdown (2026)
Here’s what gate repair actually costs in the San Antonio market this year. These ranges reflect what we see across neighborhoods like Alamo Heights, Stone Oak, Helotes, and Schertz, accounting for local labor rates and parts availability.
| Repair Type | Typical Cost Range | What’s Included |
|---|---|---|
| Limit switch adjustment or replacement | $95 – $185 | Labor plus the switch; recalibrates where the gate stops |
| Photo eye / safety sensor realignment | $85 – $160 | Labor; occasional sensor replacement adds $40 – $70 |
| Gate opener circuit board replacement | $225 – $550 | Control board, labor, and reprogramming remotes |
| Gate opener motor replacement | $350 – $850 | Motor unit, labor, and testing under load |
| Full gate opener replacement (unit + install) | $650 – $1,400 | New opener, mounting, wiring, remote programming |
| Hinge repair or replacement (swing gates) | $150 – $400 | Hinges, hardware, and realignment |
| Slide gate roller or track repair | $180 – $475 | Rollers, track alignment, and lubrication |
| Weld repair on steel gate frame | $150 – $500 | On-site welding, grinding, and rust treatment |
| Remote control programming or replacement | $40 – $95 | New remote (if needed) plus programming |
| Keypad installation or replacement | $120 – $250 | Weatherproof keypad and wiring |
What Drives the Price Up or Down
The single biggest cost driver is parts specificity. A LiftMaster or FAAC control board costs more than a generic aftermarket board, but it lasts longer and matches your system’s wiring exactly. At Calder Gate Repair San Antonio, we’re factory-familiar with nine major opener brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because a Mighty Mule homeowner in a place like Converse or Universal City shouldn’t pay for a tech who has to Google their opener model on site.
The second driver is access and gate condition. A gate that hasn’t been serviced in years often needs multiple fixes at once: the opener may have been straining against a sagging hinge for months, which burns out the motor prematurely. Rust is also a real factor in San Antonio’s humidity, especially on older steel gates in neighborhoods like Terrell Hills or Olmos Park where some installations date back decades.
The third driver is urgency. Same-day service doesn’t cost more at Calder, but if you call at 2 a.m. because your gate won’t close and you need it secured before morning, expect emergency dispatch rates to apply. A live person answers every call 24/7 at (361) 314-4803, and we’ll tell you the pricing honestly before anyone rolls a truck.
What Affects Gate Repair Pricing in San Antonio
San Antonio has some unique factors that out-of-town pricing guides miss. Here’s what actually moves the needle here, beyond the universal basics of parts and labor.
- Gate type: swing versus slide. Slide gates dominate newer construction in Stone Oak and Cibolo, and their roller and track systems wear differently than swing gate hinges. Slide gate repairs often cost slightly more because the track itself may need realignment, which takes time.
- Opener brand and age. A 15-year-old DoorKing opener in Alamo Heights is a different repair than a 5-year-old Ghost Controls unit in Boerne. Older boards are harder to source, and sometimes the honest recommendation is replacement rather than repair, which changes the price conversation entirely.
- Gate weight and material. Heavy ornamental steel gates, common in Dominion and Shavano Park, put more strain on hinges, motors, and limit switches. When a motor fails on a heavy gate, the replacement needs more horsepower, and that raises the parts cost.
- Summer heat and soil movement. San Antonio’s expansive clay soil shifts with drought and rain cycles. That movement pulls gate posts out of alignment slowly over time, which then stresses the opener. Homeowners in areas like Fair Oaks Ranch often see hinge and post issues that drivers in rockier soil don’t deal with.
- How long the problem has been ignored. A gate that’s been grinding or straining for six months has usually damaged more than one component. A squeaky hinge left alone becomes a bent hinge pin, which becomes a motor that overheats daily. Early calls are cheaper calls.
- Wiring and control setup. Gates with intercom systems, vehicle detection loops, or multiple keypads have more failure points. A gate with just a simple remote and keypad is faster to diagnose and cheaper to fix.
Common Gate Problems and What They Cost to Fix in San Antonio
Most of our calls in San Antonio fall into a handful of categories. Here’s what we typically find and what the repair runs.
Gate Opener Won’t Respond
When the opener doesn’t respond to a remote, keypad, or the wall button, the culprit is usually the control board or a blown fuse, and occasionally a failed transformer. Repair typically runs $120 to $300 if we can replace a fuse or a single board component. If the full control board is fried, replacement costs $225 to $550 including programming. A Mighty Mule or Ghost Controls board tends to run on the lower end; Viking and FAAC boards cost more.
Gate Stops Mid-Cycle or Reverses Unexpectedly
This usually points to the limit switch, the small sensor that tells the gate when to stop. A misaligned limit switch is a quick fix at $95 to $185. But if the gate reverses because the photo eye sensors are dirty or knocked out of alignment, that’s often a $85 to $160 fix, and sometimes just a cleaning. Both are common after San Antonio thunderstorms, which leave debris and sometimes shift sensor brackets.
Gate Grinds, Squeals, or Shakes While Moving
Noises mean mechanical wear, not electronics. For swing gates, worn hinges are the usual suspect at $150 to $400. For slide gates, it’s rollers and track at $180 to $475. We see a lot of this on older properties around Castle Hills and Monte Vista, where gates may be 20-plus years old. Ignoring the noise for too long is how a $200 hinge repair becomes an $850 motor replacement.
Gate Sags or Won’t Latch
A sagging gate is usually a hinge problem, a post problem, or both. If the hinges are intact but the post has shifted due to soil movement, the fix might involve resetting the post, which runs $200 to $600 depending on whether concrete work is needed. If the lock or latch fails but the gate itself is aligned, a new latch assembly runs $80 to $180.
Gate Opener Runs But Gate Doesn’t Move
You hear the motor humming but the gate stays put. That’s usually a broken gear, chain, or belt inside the opener. Repair costs $180 to $400. On older LiftMaster and Linear units, the plastic drive gears are a known weak point. If the motor itself has seized, replacement runs $350 to $850. In cases where the opener is 12-plus years old, we’ll give you the honest math on repair versus replace before any work starts.
How Much Does Gate Opener Replacement Cost in San Antonio?
A full gate opener replacement, including the unit, installation, wiring, and programming of remotes and keypads, runs $650 to $1,400 in San Antonio. The spread depends on horsepower, brand, and whether you’re replacing a swing arm opener or a slide gate opener.
- Mighty Mule and Ghost Controls openers (popular for residential swing gates): $350 to $750 installed.
- LiftMaster residential slide gate openers: $600 to $1,100 installed.
- FAAC, BFT, and Viking openers (common on heavier gates and larger properties): $800 to $1,700 installed.
- DoorKing and Elite openers (frequent on HOA communities and ranches): $900 to $2,000 installed.
These numbers assume a standard single-family residential gate. HOA entry gates, ranch gates, or custom ornamental gates with intercom and vehicle detection systems push higher. Calder Gate Repair San Antonio handles all of it, and every job gets a written price before the first bolt turns.
Repair vs. Replace: How to Decide
If your opener is under 8 years old and the repair cost is under half the price of a new unit, repair usually makes sense. If your opener is over 12 years old and you’re looking at a control board plus motor issue, replacement is often the smarter money, because you’ll likely face another failure within a year or two. A good rule of thumb for San Antonio homeowners: take the repair estimate, multiply it by two, and if that number equals or exceeds the cost of a new opener, replace instead.
We also factor in the brand. A 10-year-old LiftMaster with a bad board is often worth repairing. A 10-year-old off-brand unit with the same failure is usually a replacement, because parts availability becomes a problem and the opener’s remaining lifespan is questionable. Nico Alvarez, who leads Calder Gate Repair San Antonio, has the same conversation with every customer: here’s what it costs to fix, here’s what it costs to replace, and here’s what we’d do if it were our gate.
How to Save on Gate Repair
Saving money on gate repair isn’t about finding the cheapest tech on the internet. It’s about catching problems early and avoiding repeat visits.
- Don’t ignore small noises. A squeak is a hinge telling you it’s drying out. A $95 hinge service beats a $650 opener replacement. We see this weekly in neighborhoods like Timberwood Park and Hollywood Park.
- Test your safety sensors monthly. Dirty or misaligned photo eyes cause false reversals and put strain on the opener. Wiping them down takes two minutes and prevents a $160 service call. Note: if your gate is heavy or your opener involves high-tension springs or cables, do not attempt DIY adjustments. Spring and cable work on any gate system can cause serious injury. Let a trained professional handle anything involving tensioned components.
- Keep the track clear on slide gates. San Antonio’s oak leaves, gravel, and monsoon-season debris build up in tracks. A track obstruction forces the motor to work harder, shortening its life. Clearing the track regularly is free.
- Ask for a written price before work starts. Every Calder job includes this automatically. If you’re calling other companies and they won’t give you a number in writing, that’s a red flag.
- Get a free estimate. Calder Gate Repair San Antonio offers free estimates on every job. Call (361) 314-4803 and you’ll get a real number, not a vague range that balloons later.
- Check your warranty. Many opener manufacturers warranty their boards for 2 to 5 years. If your unit is within warranty, the part may be free and you’re only paying labor. We’ll check this for you before quoting.
Why Choose Calder Gate Repair San Antonio
Calder Gate Repair is the dedicated gate repair specialist inside the Relay Home Co. family, founded in 2009. Each location is independently owned and operated, and the San Antonio shop is led by Nico Alvarez. We fix gates, electric gates, and gate openers, and we’re factory-familiar with nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Three guarantees come with every job, and they’re never optional add-ons:
- Written price before any work starts. The number you agree to at the door is the number on the invoice. Always.
- Written guarantee on every repair. Covered by the 365-Day Done Right Promise: if the repair fails within 365 days, Calder returns at no charge. If it’s not done right, Calder makes it right.
- Free second visit if the repair fails. Included with every repair. No fine print, no exclusions beyond normal wear.
The Relay Standard defines the booking-to-invoice experience: a live arrival time you can track, not a four-hour window. Background-checked, uniformed technicians. Before-and-after photos of the work. A digital invoice you pay from a link. And a live person answers every call, 24 hours a day, 7 days a week, at (361) 314-4803. No voicemail, no chatbot.
FAQs: Gate Repair Cost in San Antonio
How much does a typical gate repair cost in San Antonio?
Most gate repairs in San Antonio run $185 to $650, with the average service call landing between $275 and $450 including parts and labor. Simple fixes like sensor realignment cost under $200, while control board or motor replacements can exceed $500. Calder Gate Repair San Antonio gives you a written price before any work starts, so there’s no guessing. Call (361) 314-4803 for a free estimate.
Is it cheaper to repair or replace a gate opener?
If your opener is under 8 years old and the repair is less than half the cost of a new unit, repair is usually cheaper. If your opener is over 12 years old with multiple failures, replacement at $650 to $1,400 installed often makes more long-term sense. Nico Alvarez walks every San Antonio customer through the math before recommending a path.
How much does it cost to fix a gate opener that won’t open?
A gate opener that won’t respond typically costs $120 to $300 to repair if it’s a fuse, transformer, or a single board component. A full control board replacement runs $225 to $550. We diagnose the exact issue and quote a written price before touching anything.
Can you fix my gate the same day?
In most cases, yes. Calder Gate Repair San Antonio dispatches technicians across the San Antonio metro daily, and a live person answers calls 24/7 at (361) 314-4803. If you call before noon, same-day service is often available, especially for urgent issues like a gate stuck open.
How much does a new gate opener cost installed in San Antonio?
A new gate opener installed in San Antonio runs $650 to $1,400 for residential applications. Mighty Mule and Ghost Controls units sit at the lower end at $350 to $750 installed, while FAAC, Viking, and DoorKing openers for heavier gates run $800 to $2,000 installed. Your written quote covers the unit, installation, wiring, and remote programming.
Do you charge extra for emergency gate repair?
Emergency dispatch rates apply outside normal hours, but you’ll always know the price before a truck rolls. A live person answers 24/7 at (361) 314-4803, and we’re upfront about emergency pricing. If your gate is stuck open and your property is unsecured, call us, and we’ll give you honest numbers immediately.
Get a Free Gate Repair Estimate in San Antonio
You don’t need to diagnose the problem yourself. Call (361) 314-4803 and tell us what your gate is doing (or not doing). We’ll give you a free estimate with real numbers, schedule a time that works, and send a background-checked, uniformed technician with a trackable arrival time. You’ll get a written price before any work starts, a written guarantee on every repair, and the 365-Day Done Right Promise backing the entire job.
Whether you’re in Alamo Heights, Stone Oak, Helotes, Schertz, or anywhere else in the San Antonio metro, Calder Gate Repair has you covered.
Pricing reflects the San Antonio market as of 2026. Calder Gate Repair San Antonio offers free estimates – call (361) 314-4803.
Written by Nico Alvarez, Owner at Calder Gate Repair San Antonio, serving San Antonio since 2009.
What Our Customers Say
"Booking was easy and the job was done quickly."
- Seth R."Swing gate arm replaced and aligned. Got photos of the old part by text."
- Nadia F."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.